ASTM E2112 – 07 PDF

Window Flashing ASTM E Presentation By: The Jacksonville Chapter, CSI. American Society for Testing and Materials (ASTM). ASTM E Standard Practice for Installation of Exterior Windows, Doors and Organization(s): American Society for Testing and Materials, ASTM. 26 Jul ASTM E Detailed information about window and door instal- lation is provided in the American Society for Testing and Materials (ASTM).

Author: Tygozilkree Mikagul
Country: Ghana
Language: English (Spanish)
Genre: Politics
Published (Last): 9 October 2004
Pages: 139
PDF File Size: 5.48 Mb
ePub File Size: 13.40 Mb
ISBN: 272-4-79224-307-7
Downloads: 89032
Price: Free* [*Free Regsitration Required]
Uploader: Akirn

Related Issues and Procedures. The installer should check with the manufacturer of factory-assembled units for instructions for anchoring. Furthermore, this practice does not purport to provide fail-safe installation methods, assurance or protection against installation deficiencies, or a standard by which architects can specify or ensure delivered performance.

ASTM E – 07 Standard Practice for Installation of Exterior Windows, Doors and Skylights

These notes and footnotes excluding those in tables and figures shall not be considered as requirements of this practice. This practice is not intended to limit or exclude other new procedures that may refine or further improve the effectiveness of fenestration installation.

Where an asbestos hazard is known or suspected, refer to the ASTM Manual on Asbestos Controland to applicable state and federal regulations. Destructive Window Replacement Fin Type. The installer should check with the manufacturer of factory-assembled units for instructions for anchoring. Installation Methods for Doors.

Historical Version s – s2112 previous versions of standard. Where an asbestos hazard is known or suspected, refer to the ASTM Manual on Asbestos Controland to applicable state and federal regulations. In the event that the manufacturer’s installation instructions provided with the product conflict with requirements of this practice, the manufacturer’s instructions shall prevail.

This practice does not cover the selection of appropriate fenestration products for a given application, nor the selection of other products or systems for use in the installation.

It may promote the deterioration of wall constructions, insulation, fenestration products, and their respective finishes.

This practice attempts to educate the installer, builder, architect, and other users in the identification and understanding of the water shedding system of the building envelope. This practice is not intended to limit or exclude other new procedures that may refine or further improve the effectiveness of fenestration installation. Link to Active This link will always route to the current Active version of the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM E2112-07: Standard Practice for Installation of Exterior Windows, Doors and Skylights

The general contractor shall be responsible for the necessary coordination of trades and proper construction sequencing of the installed fenestration product. The photo below shows attaching the fin to the sheathing using nails screws are much preferred before the subsequent application of asstm self adhering flashing.

For specific precautionary statements, see Section 5, Related Procedures. Now, I will review a newer technology that is becoming more and more innovative and popular-self adhering window flashing.

Earlier perforated asphalt impregnated felt or rosin paper supplied in smaller rolls was used in a shingle lap fashion. Work Item s – proposed revisions of this standard. The perforated perimeter fin allowed the installer to screw or nail the window to the building sheathing helping to speed the installation. Actual conditions in buildings vary greatly and, in some cases, substantial additional precautions may be required.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The design of many windows took a turn in the last 30 plus years with the innovation of the finned window.

When using field-mulled units, follow manufacturer’s recommendations and make certain that they meet applicable codes. Further, this practice attempts to consolidate and unify the various steps of construction, tying together the various trades involved with the continuity between fenestration products and the building envelope.

For specific precautionary statements, see Section 5Related Procedures. Flashing had usually been done using asphalt impregnated paper on a roll from to six to twelve inches wide.

When using field-mulled units, follow manufacturer’s awtm and make certain that they meet applicable codes. Selection of Installation Method.

It does not cover the fabrication or assembly of multiple units, whether such fabrication takes place in a factory or at the intended installation site. With the completion of this post, I leave my review of water intrusion into building walls for now.

Self Adhering Window Flashings and Related Standards | and

Active view current version of standard. All self adhering flashing must be applied to a clean dry surface at an appropriate application temperature for maximum effectiveness. The values shown in parentheses are for information only.